|
|
|
|
|||||||
| Register | Members List | Timeslips | Calendar | Sponsors | Becoming a Sponsor | Mark Forums Read | Auto Escrow | Auto Loans | Insurance |
 |
|
|
Thread Tools | Display Modes |
|
#1
09-03-2008, 02:26 AM
|
|||
|
|||
|
HELP PLEASE, no boost,black smoke
Had an oil leak from turbo pedestal.Replaced 4 o'rings. Engine started and runs OK,except when I push it. There is almost no boost 0-2 #(on the boost gauge)and a lot of blackish,brown smoke. What did I do wrong?It all went back together OK no extra parts.Please help,I'm open to all sugestions
Thanks 
|
| Sponsored Links | |
Advertisement |
|
|
#2
09-03-2008, 02:30 AM
|
||||
|
||||
|
Re: HELP PLEASE, no boost,black smoke
IC boots, Red rag in Intake, Red rag in IC tube. Can you hear the turbo?
__________________
CenTexDiesel.com Logan Schneider 830-885-6500
|
|
#3
09-03-2008, 02:43 AM
|
||||
|
||||
|
Re: HELP PLEASE, no boost,black smoke
 Make sure all your clamps are tight. Did you replace the o-ring where the compressor meets the intake spider?
__________________
Early 1999 (4/98) 7.3, Automatic, f-250 superduty, 4x4, crewcab, shortbed. CCV Mod knn intake banks exhaust banks power elbo banks turbo housing big head waste gate-disconnected Tuning by Gearhead Automotive Performance 4 gauge pod with DiPricol pyro, boost, trans temp, HPOP http://www.dieselpowerproducts.com/
|
|
#4
09-03-2008, 02:49 AM
|
|||
|
|||
|
Re: HELP PLEASE, no boost,black smoke
I took off the IC tubes,clear.I flushed water thru the intercooler,it flowed good,then blew out with hot pipe connected and cold pipe disconnected at intercooler started engine to blow out excess water. If a rag is in the IC,how can I get it out?
Thanks for replying
|
|
#5
09-03-2008, 02:57 AM
|
|||
|
|||
|
Re: HELP PLEASE, no boost,black smoke
I went over the entire system,rechecking all connectors,clamps,but I did not replace the large o'ring,it seemed OK,I don't think it could create my problem.My first inclination,was,that I left a rag in the IC pipe.That is why I took it all apart.
|
|
#6
09-03-2008, 02:59 AM
|
||||
|
||||
|
Re: HELP PLEASE, no boost,black smoke
Did you put the red line back on the wastegate?
Did you hook the rod back onto the EBPV?
|
|
#7
09-03-2008, 04:03 AM
|
||||
|
||||
|
Re: HELP PLEASE, no boost,black smoke
Did you put red rags on top of the heads? maybe put the spyder down without taking one out?
|
|
#8
09-03-2008, 06:29 PM
|
||||
|
||||
|
Re: HELP PLEASE, no boost,black smoke
Is the collector securly attached to the back side of the turbo?
__________________
2001 F250, CCSB, 4X4, Auto, Forged rods
Lots of go fast parts and still slow. 2001 F250, STD cab, 2WD  Frame is a little shorter now workin on body engine build underway
|
|
#9
09-04-2008, 03:57 AM
|
|||
|
|||
|
Re: HELP PLEASE, no boost,black smoke
You guys are alright.Thanks for all the replies.I'll go over it again,starting with the collector to turbo and clamp.
Thanks again
|
|
#10
09-05-2008, 03:04 AM
|
|||
|
|||
|
Re: HELP PLEASE, no boost,black smoke
With all the replies,I found the problem.The actuator arm came off the waste gate valve pin.
Thanks again, to all who replied
|
|
(View-All)
Members who have read this thread : 66
|
|
| 0373, 2kstroker, 97PSD350, 99coalroller, 99F250Smitty, alumguy, Arisley, bigd4me2, BigRed97, big_stroker, BMac, BoilermakerSteve, brandon_7, c125bob, chewbacca, crowz, Dantheman, Deepsky3539, Deputydog, Dieselfever, Dieselgeek, doubledoor, ELKHUNTER, F-DuceFifty, fastco5, fbilly420, Firedogbme, fishinfool98, golfer, Greg373, Haul_n_horses2, JimTJr, kyle@DI, Logan21SV, Martin #6, matthewd11, mattrac, muddy_one, newmexicocrawler, PHPDiesel, Ramblin'_Man, rconcrete, redmist, rocketron, Rockrunner86, Rogue1970, rpm-inc, S&RTransport, sagebel, sirnunya, spb_2006, Stiletto6.0, Stites02psd, straitcountry, stroker99, StrokerTurbo7.3, stroketeck, SUPERDF350, theSLEEPER, Thuglike, tienanh4m, TrailerHauler, urbanwheeler, Wheels |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
